Airforce Gunpower Larger Plenum Regulator

Airforce Larger Plenum Regulator for .250/.257/.308/.357/.457 (V2) (First of its Kind for the Airforce and Gunpower Big Bore Airguns)

For all those people out there looking for a larger plenum to shoot slugs off their Airforce Airguns, we now have it for you.

Dual Gauge which shows both the regulated pressure and the tank pressure.
Output range of the regulator can be internally adjusted from 100 bar to 200 bar.
(We have tested it to an output (plenum pressure) of 400 bar as shown in above video)
Max fill pressure of the regulator is 300 bar. (Make sure of your tank max working pressure and fill no more than the recommended pressure)
(Tested to a fill pressure of 500 bar as shown in above video)
We have been working on this for quite some time and have been periodically testing these regulators for utmost performance.
We can proudly say that our regulators are now available for sale and will do a great job on the Airforce Texan and the Gunpower Big Bore Airguns across the wide range of cals from .250 / .257 / .308 / .357 and the .457.

Dual Gauge design:
No more guessing, what pressure the regulator is set at.
Gauge shows you the output (Regulated pressure) as well as the input pressure. (Tank pressure).
No more keeping track of shot counts or guessing and working hard to know the cut off pressure of your regulators.
Regulator comes factory set at 200 bar.
If you would like it to be set to a lower pressure, do write in the comments when you place the order and it will be pre-tuned and shipped.

Foster fill nipple on the regulator for quick fill or tethering your airgun.
This regulator ensures that your tank retains the quick install and disconnect feature.
You don't want to be looking for the Spin-Loc Tool when you want to get started or done shooting.

You will not be using the fill nipple/gauge on the factory valve anymore. Can be plugged with dead end caps. “Airforce/Gunpower Valve assembly NPT Dead End Plugs”

Post upgrade always fill using the male qd (male foster fitting) on the body of the regulator.

Largest Plenum available in the market on our regulators, help combine both power and consistency shot to shot.
Built like a tank and tested to 500 bar for safety. (Never Exceed the max fill of 300bar input pressure)
(Tank must be rated to 300 bar) and output pressure (plenum output pressure of 200 bar)

Sturdy gauges with metallic body for the wilderness with the airforce and gunpower big bore airguns.
With the reg set at 150 bar we shot the lyman 150gr collar button at 940 fps, and they were mighty accurate at long ranges.
The shot count would depend on what buddy bottle you have attached onto the regulator.
Larger the buddy bottle higher the regulated shot count.
It wouldn't matter if you are shooting the airgun tethered as you have a continuous supply of air to the regulator and thereby a greater number of regulated shots.
Each regulator is filled to 300 bar (input pressure) with the reg output (plenum pressure) set to 200 bar for 24 hours before they ship to ensure they are free of leaks.
The best raw materials have been used to machine this regulator and to ensure we have a light, durable, safe and proven product.
They have been chosen, designed with materials and specs to the highest tolerances for the right job.
Safety is the highest priority for any of the products we manufacture.

If you need the max shot count then the answer to it is our "1 Ltr Luxfer Carbon Composite Cylinders 300BAR (61cu)(1000cc)"
If you have your own tank with M18 x 1.5 threads, then it would be a direct fit as well.

We have now launched a “Airforce Condor Regulator Adjust Regulated Pressure Assembly” for those who would like to easily adjust the regulated pressure.

Imp Note: Sale is only for the Regulator. You will be using the factory valve assembly which installs onto the mouth of the regulator (unless you have purchased a custom valve assembly from us) and the reg then screws into the factory buddy bottle you already have. (unless you have purchased a buddy bottle of higher rating and/or capacity)

BE SURE TO READ THE DOC FOR INSTALLATION WHICH IS SENT ON EMAIL BEFORE YOU BEGIN THE UPGRADES.

[MAKE SURE TO DEGAUSS THE TANK BEFORE ATTEMPTING THE UPGRADE. ONCE DEGAUSSED, YOU SHOULD BE ABLE TO PRESS THE VALVE WITH YOUR HANDS AND THERE SHOULD BE NO PRESSURE IN THE TANK. ALWAYS DOUBLE CHECK THE SAME BEFORE YOU START WITH THE DISSASSEMBLY)

Length increased post Installation on factory setup: 118.90mm/4.68in

Plenum Volume: 151cc

If you have any further query about the listed product you can use the above link to “Ask a Question”